Nvidia 400 User Manual download pdf (Page 58)

S-ATA RAID Configuration

Page 5-4

Enable RAID Function

For any RAID controller, the general procedure to setup a RAID system is shown

below:

Step 1: Create RAID Array

RAID arrays are created using the RAID controller’s BIOS utility.

NVIDIA nForce2 MCP

Power-on the system and wait for the following screen to appear. Press the

”F10” key to enter its BIOS configuration utility.

Refer to Appendix B-1 for details about creating RAID array using this utility.

After the RAID array is created, press “F10” to exit.

Note: If you are not installing O/S into the RAID

disks, you may skip Step 2 & Step3.

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 77 78

Manual Revision 1.0 1
July 05, 2004 1
DISCLAIMER OF WARRANTIES: 2
Initial Keyboard 3
Table of Contents 4
Section 1 Introduction 4
Section 2 Specification 4
Section 3 Installation 4
Section 4 BIOS Setup 4
Section 6 Driver Installation 5
Appendix Appendix A 5
Appendix B 5
Appendix C 5
Page Left Blank 6
Section 1 7
INTRODUCTION 7
Page 1-3 9
Introduction 10
Page 1-4 10
1-3 System Block Diagram 11
Page 1-6 12
Section 2 13
SPECIFICATION 13
Page 2-2 14
Page 2-3 15
Page 2-4 16
Section 3 17
INSTALLATION 17
Page 3-2 18
Page 3-3 19
Page 3-5 21
<Figure 6> 21
<Table 1> 21
AGP Card Installation Caution 22
Page 3-7 23
Page 3-8 24
Page 3-9 25
Page 3-10 26
Page 3-11 27
Page 3-12 28
CAUTION ! 28
CFP: Front Panel Connector 29
Page 3-14 30
12V 4-pin 30
Page 3-15 31
Page 3-16 32
Section 4 33
BIOS SETUP 33
Page 4-3 35
Boot Other Device 35
Page 4-4 36
Boot Up Floppy Seek 36
Security Option 36
Full Screen LOGO Show 36
Page 4-8 40
Init Display First 40
Onboard Device 42
Onboard I/O Chip Setup 43
Page 4-14 46
ACPI Function 46
ACPI Suspend Type 46
Power Management 46
Page 4-16 48
PwerOn After Pwr-Fail 48
Resources Controlled By 48
VGA cards 49
Options: Enabled, Disabled 49
Page 4-19 51
Chipset Voltage 51
Dimm Voltage 51
Battery Voltage 51
Power Supply + 5V, 5V Standby 51
Page 4-20 52
CPU Voltage Regulator 52
AGP Voltage Regulator 52
DIMM Voltage Regulator 52
Chipset Voltage Regulator 52
ENTER PASSWORD: 53
PASSWORD DISABLED 53
Page 4-22 54
Section 5 55
S-ATA RAID CONFIGURATION 55
RAID 0 (Striping) 56
RAID 1 (Mirroring) 56
JBOD (Spanning) 56
Page 5-3 57
Page 5-4 58
NVIDIA nForce2 MCP 58
Page 5-5 59
Page 5-6 60
Section 6 61
DRIVER INSTALLATION 61
 Introduction 62
Page 6-3 63
Page 6-4 64
Page 6-5 65
Page 6-6 66
Page 6-7 67
Drivers Installation 68
Appendix A 69
Appendix 74

Comments to this Manuals

No comments

Nvidia 400 User Manual Page 58

Comments to this Manuals

Related products and manuals for Motherboards Nvidia 400